Compare Pool Types by Cost
The cheapest pool to build is rarely the cheapest to own. This tool runs all four types — concrete/gunite, fiberglass, vinyl-liner and above-ground — through the same cost engine on identical assumptions (same size, climate, usage and electricity price), then lines up their installation, yearly running cost, replacement cycles and total cost over the years you plan to own the pool.
Only what genuinely differs by construction type changes between the columns: the base build price, the electrical work, and the replacement schedule — concrete is resurfaced, fiberglass’s gelcoat is refinished on a long cycle, and vinyl and above-ground pools get a new liner. Energy, water and chemicals are held equal, because the model does not differentiate them by shell. Every figure is sourced and shown with its confidence grade.
Calculator
Installation is shown with the standard essentials on (electrical, permits, initial water fill and a code-required fence) and optional upgrades off — so the four builds are compared like-for-like.
Cheapest to own over 10 years
Above-ground · $28,500
Most expensive is Concrete (gunite) at $103,000 — a $74,500 spread over 10 years.
| Over 10 yrs | Concrete (gunite) | Fiberglass | Vinyl liner | Above-groundLowest total (cheapest to own) |
|---|---|---|---|---|
| Total over horizon | $103,000 | $88,000 | $82,500 | $28,500 |
| All-in / year | $10,500 | $8,800 | $8,250 | $2,850 |
| All-in / month | $860 | $730 | $690 | $240 |
| Installation (one-time) | $86,983grade C | $71,983grade C | $61,983grade C | $11,483grade C |
| Operating / yearsame for every type | $1,400 | $1,400 | $1,400 | $1,400 |
| Replacements (in horizon) | $1,800 | $1,800 | $6,300 | $2,800 |
| Set-aside / month (long-run) | $76 | $57 | $69 | $31 |
Total cost of ownership over 10 years
- Concrete (gunite)$103,000
- Fiberglass$88,000
- Vinyl liner$82,500
- Above-ground$28,500
Concrete (gunite)
install grade CShotcrete/gunite shell, fully customizable in shape and finish. Highest upfront cost and the highest long-run upkeep: the plaster finish is resurfaced on a cycle and the chemistry runs a little hotter.
Replacement cycles
- Resurface (plaster) ~12 yr
- Pump ~7 yr
- Filter (vessel) ~15 yr
- Filter media ~4 yr
Fiberglass
install grade CPre-molded shell dropped into the excavation. Fast install and low long-run upkeep — no liner to replace and no plaster to resurface, though the gelcoat surface is refinished on a long cycle. Fixed shapes and sizes.
Replacement cycles
- Gelcoat refinish ~20 yr
- Pump ~7 yr
- Filter (vessel) ~15 yr
- Filter media ~4 yr
Vinyl liner
install grade CSteel or polymer wall frame with a vinyl liner. Often the lowest in-ground entry price, offset by replacing the liner every several years.
Replacement cycles
- Vinyl liner ~9 yr
- Pump ~7 yr
- Filter (vessel) ~15 yr
- Filter media ~4 yr
Above-ground
install grade CFar cheaper to install and remove, with lower operating costs for a smaller volume of water. Its liner and (cheaper) equipment are replaced periodically; enter real figures for a precise number.
Replacement cycles
- Liner (above-ground) ~8 yr
- Pump ~7 yr
- Filter media ~4 yr
What’s equal, what isn’t, and how sure we are
- Energy, water and chemicals are identical in every column. The model does not vary operating cost by shell type — so the “Operating / year” row is the same for all four. Real-world differences exist (e.g. a smooth gelcoat can need slightly less chemistry) but no independent source quantifies them, so none is invented here.
- Install prices are cost-guide estimates (grade C), shown as typical defaults; the real spread is wide. Most replacement costs are grade D, and the fiberglass gelcoat refinish is a thin-sourced grade-D figure that only affects long horizons.
- Above-ground reuses the shared pump cost, which overstates a small above-ground pump, and is compared at the same size as the in-ground types — above-ground pools are usually smaller, so lower the size to match a real one.
- Results are planning estimates. For a precise figure on one type — your own quote, add-ons, finish and component ages — use the full calculator, or see how we calculate every figure.
Did this calculator give you what you needed?
See a number that looks off?
Calculation Formulas
Every type is run through the same cost model on ONE shared set of assumptions (size, climate, usage, electricity price and horizon). Only the type-intrinsic factors differ: the base install price, the type’s electrical default, and its replacement schedule — concrete is resurfaced, fiberglass’s gelcoat is refinished, vinyl and above-ground pools get a new liner. The operating lines (pump electricity, make-up water, chemicals, maintenance, heating) are IDENTICAL across types, because the model does not differentiate them by shell material — a limitation shown on the page, not hidden.
N is the number of years you plan to own the pool. The one-time install is paid once; operating costs recur every year; and each replacement is a DISCRETE event in the year it actually happens — only events within your horizon are counted as cash. A 7-year pump in a 10-year horizon is replaced once (year 7); a 12-year resurface in a 10-year horizon is not charged at all.
The base is a typical default per pool type (grade C–D; no government data) and includes excavation, plumbing, standard pump/filter, a basic finish, and coping + a ~3 ft apron. ESSENTIAL ancillaries are on by default — electrical & bonding (D), permits (F; enter your own), the initial water fill (computed from pool volume × the EPA water rate, grade B), and a code-required fence (D; $0 if you already have a compliant one). OPTIONAL upgrades (heater, cover, lighting, additional decking, landscaping, rock/haul-off/access adders) are off by default and never hidden in the base. A turnkey base that already includes decking suppresses the separate decking line; the included apron is never suppressed.
Each component (pump, filter, liner, resurface, gelcoat, salt cell, heater) is scheduled in the year it occurs — first at its interval for a new pool, or sooner for an existing one you give an age to (an overdue part lands in year 1, never year 0). The CASH number counts only events within your horizon. Separately, the long-run SET-ASIDE (Σ cost ÷ interval) is the stable monthly budget for everything, whatever your horizon; and WEAR shows capital consumed but not yet paid at the horizon’s end — informational, never in the cash total. Pump and heater intervals come from DOE rules, and the vinyl-liner interval from the dominant manufacturer’s SEC filing (grade B); every replacement cost is a cost-guide or repair-contractor estimate (grade D).
Pump energy is computed from its drivers — running watts, hours per day and the season length — then priced at your electricity rate (EIA U.S. average by default, grade A). Make-up water is computed too: surface area × net evaporation (in/yr) × 0.623 × (1 − cover) gallons, priced at EPA water (and optional sewer) rates (grade B). Heating, if on, is a cover- and surface-area-scaled figure per active heating month × the number of heating months (grade C; gas the least certain). Chemicals and maintenance stay full-year cost-guide estimates you can override.
Key Figures
| Figure | Value | Description |
|---|---|---|
| Electricity price | $0.182/kWh | U.S. residential average, EIA STEO Nov 2026 (grade A). State prices vary ~12–53¢ — enter your own rate. |
| Pump energy (computed) | W × h/day × days ÷ 1000 | Variable-speed default 320 W × 12 h; single-speed 2000 W × 6 h (DOE/NREL/FSEC, grade B). Anchors: ~2,400 kWh/yr single, ~800 kWh/yr variable over a 7-month season. |
| Climate (season & evaporation) | 210 days · 45 in/yr | National baseline (grade C); regional presets 28–85 in/yr are grade B (EPA/SNWA/CUWCC/AZ DWR). No invented per-state cost. |
| Chemicals | $500/yr | Chlorine pool, ~20k-gal Sun Belt midpoint (grade C, estimate); range $200–$1,350. Saltwater is roughly break-even, not simply cheaper. |
| Maintenance (DIY / service) | $600 / $1,400/yr | DIY supplies vs a professional contract (grade D, cost-guide estimate); service range $960–$2,400. |
| Make-up water (computed) | area × evap × 0.623 × (1 − cover) | Gallons priced at the EPA WaterSense 2024 rate of $9.13/1,000 gal (grade B). WATER-ONLY by default; sewer (+$9.59/1,000 gal) is added only where you enable it. 0.623 gal = 1 inch over 1 sq ft. |
| Pump replacement | $1,300 / 7 yr | Interval grade B (DOE 7-yr mean); cost grade D. Every pool type. |
| Filter (vessel · media) | $1,200/15yr · $250/4yr | Vessel cost grade D; media interval grade C (Hayward sand life). |
| Vinyl liner | $4,500 / 9 yr | Cost grade D; vinyl pools only (Latham SEC 10-K: 8–10 yr). |
| Resurface (finish-specific) | $7,000/12yr · $8,500/12yr · $11,000/18yr | Plaster · quartz · pebble (concrete only). Intervals grade C (NPC); costs grade D. |
| Salt cell · heater (optional) | $900/~5yr · $4,500/11yr | Salt cell only with saltwater (life from pump hours, grade C); heater only when heated (DOE 10–11 yr, interval grade B; cost grade D). |
| Install — Concrete (gunite) | $50,000–$120,000 | Typical default base price (grade C, estimate — no government data); the range is the low/typical/high span. Electrical, permits, water-fill and a code fence are added as separate ESSENTIAL lines; decking and other upgrades are OPTIONAL. |
| Install — Fiberglass | $45,000–$100,000 | Typical default base price (grade C, estimate — no government data); the range is the low/typical/high span. Electrical, permits, water-fill and a code fence are added as separate ESSENTIAL lines; decking and other upgrades are OPTIONAL. |
| Install — Vinyl liner | $35,000–$80,000 | Typical default base price (grade C, estimate — no government data); the range is the low/typical/high span. Electrical, permits, water-fill and a code fence are added as separate ESSENTIAL lines; decking and other upgrades are OPTIONAL. |
| Install — Above-ground | $1,600–$7,500 | Typical default base price (grade C, estimate — no government data); the range is the low/typical/high span. Electrical, permits, water-fill and a code fence are added as separate ESSENTIAL lines; decking and other upgrades are OPTIONAL. |
Note: Results are planning estimates. Pool prices, energy rates and upkeep vary by region, pool size and contractor — confirm exact figures with a local pool professional and your utility before you commit.
Want the full picture? See the complete sources & methodology behind every default.
Standards & Sources
Last verified: November 2026
- U.S. DOE — Energy Saver: pool pumps & heaters
Pool-pump annual energy use (kWh) and heat-pump vs. gas heating cost, the basis of the energy and heating lines.
- U.S. EIA — electricity price
Average U.S. residential electricity price (~18.2¢/kWh, 2026), multiplied by pump kWh for the energy line. Per-state table being added.
- 2026 pool cost guides (HomeGuide, Angi, This Old House, NerdWallet)
Installed cost by pool type, chemical, maintenance, liner, resurfacing and equipment ranges. Treated as estimates and shown with their range, since pool cost has no single authoritative benchmark.
- Low / Typical / High scenarios
Three fixed, coherent example configurations — not the minimum or maximum of every input. Each override stays within the documented A–D ranges and keeps its grade; pool type, electricity price, finish and all formulas are held constant. Typical reproduces the default flagship exactly; cash, set-aside and wear stay distinct.
How to use this calculator
- Set the shared assumptions — ownership length, pool size, climate, cover and whether you heat the pool. They apply to all four types equally.
- Read the side-by-side table: installation, operating cost per year, the replacement cash that falls within your horizon, and the total cost of ownership.
- Check the major replacement cycles for each type — resurfacing, a new liner or a gelcoat refinish — and the confidence grade on each figure.
- Compare the total over your horizon; the cheapest to build and the cheapest to own are often different pools.
- Change the ownership length to see the ranking shift — short horizons favour cheaper builds, long horizons reward low-upkeep types.